pNeuton mini

Ventilator

Neonatal or infant critical life support in the A&E, MRI, OR, ICU and transport.

The pNeuton mini Ventilator provides ventilatory support to neonatal, infant and pediatric patients, and accommodates even the most fragile patients from 400 grams to 25 kilograms.

A fully pneumatic ventilator, the pNeuton mini is built to support patients non-invasively using nasal prongs / masks for CPAP application, or ventilation + CPAP with endotracheal tubes for full support.

With a built-in oxygen blender, and precise timing & pressure controls, the pNeuton mini matches the complexity of pressure-limited ventilation in standard infant ventilators.

The pNeuton mini is also compatible with the Life Pulse High-Frequency Jet Ventilator from Bunnell Incorporated to provide conventional ventilation in tandem with the Life Pulse without interfering with high frequency ventilation or nuisance alarms. This broadens the clinical application and prepares the clinician to meet patient needs during transport.

The pNeuton mini easily accommodates air or ground transport, as well as within the hospital. Due to Its unique pneumatic design, the mini is always ready to go – anytime, anywhere.

UNIQUE ADVANTAGES

Fully pneumatic – No batteries or electricity needed
Invasive or non-invasive ventilation
Built-in oxygen blender, and precise timing & pressure controls
Ideal for transport within the hospital as well as via ground or air
Compatible with the Life Pulse High-Frequency Jet Ventilator from Bunneli Inc.
MRI compatible up to 3T – can be placed next to the magnet with remote alarm
Small, lightweight, portable
Easy-to-use controls
Made in Melbourne, Florida, USA

Benefits

BENEFITS FOR THE PATIENT

A wide range of continuous flow settings to provide the right ventilation for the size of your patient with the least amount of expiratory flow resistance
Adjustable oxygen delivery from 21% to 100% to precisely match patient oxygen requirements
Switch from CPAP nasal prongs, face mask to mechanical ventilation seamlessly and without interruption
One ventilator with no change in patient circuit wherever patient care and diagnostic procedures are needed

Benefits for You, the Healthcare Provider

Calibrated controls for precise and easy operation
Night visible manometer to monitor patient pressure and effort
Patient disconnect and high-pressure alarms that work during non-invasive and invasive ventilation
MRI conditional up to 3 T – place right next to the scanner with remote alarm output for the control room
Oxygen powered – no electrical connection or batteries
Rugged and tested to meet airworthiness standards with everything built-in – no accessories needed
Protection for the caregiver from patient exhalation using the bacteria / viral filter

Benefits for your Budget

Switch from invasive ventilatory support to non-invasive with just a simple change of the patient interface
Lightweight and portable with attachment to any patient care incubator/bed
Minimal oxygen consumption to maximize transport times
No batteries or electronics decrease preventative maintenance costs

Applications

pNeuton mini Ventilator is designed for

A&E
MRI
OR
NICU
Air, ground, or Intra-hospital transport

Product Information for the pNeuton mini Ventilator

Specifications

pNeuton mini P/N 20031

DESCRIPTION

Pneumatically powered for use on neonatal / infant and pediatric patients
Patient range – 400 gram to 25 kilogram
Modes – CMV, IMV + CPAP or CPAP only – continuous flow pressure limited ventilation
Pressures displayed on manometer
MRI conditional – 3 T or less, maximum spacial gradient magnetic field of 720-gauss/cm or less, no gauss line restriction
Gas consumption – flow setting + 3 L/min
Size – 15.2 cm x 22.1 cm x 19.8 cm
Weight – 4 kg
Input gas requirement (oxygen and medical air): 55 psi ± 15 psi (3.8 bar ± 1 bar) each gas
Classification according to MDD 93/42/EEC: IIb
- Meets International Standards for transport ventilators:
  ASTM F1100-90 – Ventilators Intended for Use in Critical Care
- ISO 10651-3:1997 – Lung Ventilators for Medical Use- Particular requirements for emergency and transport ventilators
- Airworthiness: RTCA DO-160G – Environmental Conditions and Test Procedures for Airborne Equipment, as applicable

CONTROL SETTINGS

Inspiratory time: 0.25 to 2 seconds
Expiratory time: 0.25 to 20 seconds
Continuous Flow: 6, 8, 10, 15 or 20 L/min
Peak pressure: 15 to 60 cm H2O (mbar)
PEEP / CPAP: 0 to 20 cm H2O (mbar)
Oxygen: 21 to 100% ± 3%, requires oxygen and medical air source

AUDIBLE AND VISUAL ALARMS

All pneumatic alarm system (no batteries – requires minimum 30 psi / 2 bar gas supply pressure)
Remote alarm output connection
- Patient circuit disconnection
- Automatic reset when alarm condition resolves
- 20-second silence/reset button
- 10-second activation
High pressure – independently adjustable from Peak Pressure
- Low gas source pressure
  If either source gas drops below 40 psi (2.8 bar)
- Continues operation as long as oxygen is available

Regulatory Compliance

International Regulatory Compliance Information

Under regulatory compliance, our goal is to take steps to comply with relevant laws, policies, and regulations for medical device manufacturing and marketing Airon products. All Airon products are designed, manufactured, and supported based upon sound quality procedures. Every device is CE marked as well as USA FDA cleared.

Product Certification and Approvals

USA – FDA Free Sale Certificate – Certificate to Foreign Government

Canada – Medical Device Licenses
pNeuton ventilator license | patient circuit license

Europe – CE Marking certificates – Airon EC Certificate

Europe – Declarations of Conformity

USA –FDA 510(k) cleared
pNeuton mini

User Resources

miniFlow NIV Application Information: English

miniFlow Patient Interface Guide: English

pNeuton mini miniflow Instructions for use: English

Product Comparison Chart: English

pNeuton mini Operational Verification Procedure: English | Svenska

pNeuton mini Self-Guided Presentation: English | Espanol | Deutsch | Francais | Svenska

pNeuton mini Introduction Video: English

pNeuton mini Preventative Maintenance Program: English

pNeuton mini Limited Warranty: English

Technical Bulletins

pNeuton mini Environmental Testing: English pNeuton mini Flight Certificate: English pNeuton mini Operating Time: English pNeuton mini MRI Testing: English pNeuton mini Manual Breaths with Bunnell Jet: English MRI Certification pNeuton Ventilators: English pNeuton mini compatibility with Bunnell Life Pulse HFV: English

pNeuton Bi-level Pressure Ventilation: English

Work of Breathing Comparison: English

Respiratory Care Test Comparison: English

NBC filter with pNeuton ventilators: English

pNeuton for disaster preparation: English

Compliance with US Army Airworthiness Standards: English

Clinical Articles

Compatibility with Bunnell Life Pulse HFV: English Clinical Applications: English

Airon Product catalog

The pNeuton ventilators/CPAP systems are critical care devices designed for use by healthcare professionals under the direction of a physician or healthcare provider.

Airon Corporation manufactures and markets innovative, reliable, effective, fully pneumatic oxygen-powered life support ventilation and CPAP products and accessories for healthcare workers worldwide. Our products support neonates, infants, pediatrics, children and adult patients in EMS, hospital A&E and trauma, MRI, OR, ICU, and transport.

Get in touch!

For more information, to arrange a demo or to ask any questions about our products, please contact us.

Contact us now